Undead Sleds / Rat Rods Rule - Hot Rods, Rat Rods, Sleepers, Beaters & Bikes... since 2007!

Go Back   Undead Sleds / Rat Rods Rule - Hot Rods, Rat Rods, Sleepers, Beaters & Bikes... since 2007! > Members List

donsrods donsrods is offline

Rusty Rat Rodder

Visitor Messages

Showing Visitor Messages 11 to 20 of 23
  1. donsrods
    07-25-2013 11:15 AM
    donsrods
    Here are the ones we like the best. Home Depot, Ace, all of them carry them and they work well.

    Don

    http://www.channellock.com/crimper.aspx
  2. IAM-LDS-2
    07-25-2013 10:32 AM
    IAM-LDS-2
    Hey Don saw a post by you on ? , about wiring and you posted a picture of wire crimper that you use . Could you tell me what the brand name is . I don't know if you recognize my screen name , used to be somebody else and have to lay low as I only lurk around here .
  3. donsrods
    02-14-2013 07:44 PM
    donsrods
    Wow, I wish I had an answer for you, but I have never played with one of those. But I do remember a guy in the magazines named Orve Elgie, or something like that, and he adapted Duster brakes to an early Dodge. If you can't find an answer here, I would post the question on the HAMB, lots of guys on there have probably done it.

    BUT , HERE ARE SOME SUGGESTIONS BEFORE POSTING:

    If you have never done an introduction on there, do one first. The introduction Nazis will jump on you if you dont. Secondly, say you are working on a 39 pickup, not a rat rod or a bobber or anything like that. They really get nuts when someone says they are just using a body like that to build a bobber with no fenders, or a rat rod.

    Just trying to keep you from getting flamed over there.

    Don
  4. kyotb8
    02-13-2013 11:57 PM
    kyotb8
    Mr. Don, I've noticed your rods and posts on here. would you happen to know if there is a fairly simple way to adapt front drums from a say 61-71 Dodge pickup to my 39 Plymouth truck front axle ? Or any other good self-energizing drum ? I'd like to keep my truck old school if possible. Thanks for your time.
  5. 21willys
    12-22-2012 01:32 PM
    21willys
    Never mind I must be lossing my mind.lol
  6. 21willys
    12-22-2012 12:54 PM
    21willys
    Do you know what happened to the thread about the stollen 32? I posted on it, then poof it was gone.

    Eric
  7. donsrods
    03-12-2012 01:45 PM
    donsrods
    When you say "pipe" is that like water pipe? If so, it is not made for using as a crossmember. Go to a steel supply house and get a piece of 3 inch DOM tubing with about an 1/8 to 3/16 wall thickness and use that. I don't think the softer spring would do that, it was just probably that the frame was twisting up front and wasn't properly gusseted. Do you have any pictures ?

    Don
  8. Ratcrazy
    03-12-2012 09:01 AM
    Ratcrazy
    Hey Don, This is Ratcrazy. Got a couple of questions.
    1) I had the front end lined up on my rpu and the tires balanced. I noticed the shackles were bottomed out so I go & buy a shorter/softer spring. Now at 50-55 or above the front tires wants to bounce back and forth, kinda up and down. That leads me to the 2nd part & the real question. I was thinking of adding a leaf to the sotfer spring and thats when I noticed a couple of stress cracks in tube at each end. This is a suicide front end. The welds are good but the tube/pipe its self is showing cracks out next to the frame rails. The rails at ok, just in the tube. The tube is 3"x1/4" wall pipe with a seam. What would you suggest that I replace the tube with? And do you think the softer spring would cause the pipe to crack like that? If possible please reply soon.
    Thanks and God bless,
    Larry aka ratcrazy
  9. lost in the 50s
    12-06-2010 07:02 PM
    lost in the 50s
    the hamb ban me also for having a finished coupe can you post my post on hamb for me thanks
  10. chipper
    01-22-2009 06:54 PM
    chipper
    hello this is Chipper i have a ? to ask you .. are there any threads on motor mounts ? thanks

About Me

  • About donsrods
    Location
    fort myers florida
    Interests
    cars

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: 12-04-2019 03:25 AM
  • Join Date: 05-11-2007

All times are GMT -5. The time now is 05:20 AM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Rat Rods Rule Inc.