Dagel' Repairs

Rat Rods Rule

Help Support Rat Rods Rule:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

gasser

Well-known member
Joined
Oct 15, 2010
Messages
118
Location
5025 Sherwood Dr Fort Worth 76114
Hi all just to let you know I am now doing repairs to all types or cars and trucks.
It does not mater if it is you daily driver ,rat rod ,Street rod, or Bus

I have a 3000 sq foot shop behind my house here at
5025 Sherwood Dr.
Fort Worth Texas 76114

I am a ASE certified master Auto, Truck, & Bus tech
Cadillac Master Tech last 2 years at the dealership (10 years at Frank Kent Cadillac)

I do all work from brakes to complete chassis builds, motors and wiring and everything in between have had customer cars in major magazines (these were ground up builds)

I am currently charging $30. an hr straight time and am fair with the hours.
I am now retired at 50, and not trying to make a killing .I have very little overhead and love working on the old cars I will even let you watch and help I you want to learn

if you need a lug nut replaced or a car built or any thing in-between I can help I prefer to use your parts but will furnish parts at 10% mark up if needed

Dan Dagel
817-626-1418
leave a message I will call back
[email protected]
 
67 chevelle

The 67 got a 502 big block, 4 sp, and the factory ac reworked
Dash was pulled a fully restores
chassis got rebuilt disc add up frount cleaned and undercoated
Ps got rebuilt
frame and fire wall were sand blasted and painted
 

Attachments

  • chevelle dash 008.JPG
    chevelle dash 008.JPG
    129.9 KB · Views: 44
  • chevelle dash 010.JPG
    chevelle dash 010.JPG
    129.9 KB · Views: 44
  • 49 chevy pu 013.JPG
    49 chevy pu 013.JPG
    127.6 KB · Views: 44
If your good with bus repair you might check out bus conversion magazine forum. It's for converted tour busses. They have a section for repair facility's that can offer service work when on the road. It's a brotherhood over there. If one guy likes you, they all like you and will use your services.
 
where we are now

I have been lurking around for a while and not posting so thought I would take a few minute share what in the shop getting knocked out 1st is a 50 Buick convertible got 500 EFI Cadillac engine next 2 are 53 ford and the my 59 5,0 EFI
been staying busy

There is a 29 model a 2dr sdn coming up been gathering parts so far I know it will have a 331 hemi with auto overdrive 4"drop axle with 45 fin Buick drums got just about everything but the quick-change rear it will be a cross between a rat rod and a traditional rod .The new wood kit will get stained and inside done in Red Oxide colored BC, Chicken wire roof and 2 seats outside will be left as is The 29 is out of Wissicon and has solid metal and no cancer

well time to get back after it
have a happy Halloween
 

Attachments

  • IMG_0230.JPG
    IMG_0230.JPG
    156.6 KB · Views: 19
  • IMG_0571.jpg
    IMG_0571.jpg
    78.8 KB · Views: 20
  • IMG_0572.jpg
    IMG_0572.jpg
    74.8 KB · Views: 21
  • IMG_0474.jpg
    IMG_0474.jpg
    84.9 KB · Views: 21
  • IMG_0478.jpg
    IMG_0478.jpg
    92 KB · Views: 19
  • IMG_0482.jpg
    IMG_0482.jpg
    53.2 KB · Views: 21
  • DSCN0883.jpg
    DSCN0883.jpg
    104.9 KB · Views: 23
  • DSCN0997.JPG
    DSCN0997.JPG
    126.9 KB · Views: 22
  • DSCN1000.JPG
    DSCN1000.JPG
    125 KB · Views: 21
  • DSCN1001.JPG
    DSCN1001.JPG
    125.1 KB · Views: 21

Latest posts

Back
Top