"Bickle" 1948 3100

Rat Rods Rule

Help Support Rat Rods Rule:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
giphy.gif


Good stuff Joe !!!!

[P[P[P
 
yep, the table is like a time machine. before I would need hours and hours to plan all the hand cuts and it wouldnt be nearly as repeatable let alone as clean. now its about an hour in solidworks, 10 min in setup, one test run plas off and a for real run.

still learning silly mistakes, like on that first pedal mount it cut the circles first and then on the long outside cut the torch would shut off when it lost the arc in the circle. oops. but learned to just back up the code and start it again.


organized the shop AGAIN, its hard when it is just me unloading because I cant move heavy stuff 50ft willy nilly.

attachment.php

attachment.php


the yellow bed out of place is for bickle, so its up by the door when I need it.

used my eastwood bender to take up all that extra in the fuel lines and rear brake line. looks like they will rub together which is bad, but I put the plastic isolation clips back on and the frame clips too, so its all better now.

attachment.php



I finished the trans mount bracing and connected the exhaust again, so time for a cab fit.

attachment.php

attachment.php


fit really well, mounts look like they will do the job! the trans ALMOST fits, I trimmed slightly and need just a hair more, the body is actually 1/4" high right now resting on the trans, but I need to move it around a little so I will see how that helps.

attachment.php


should be more today!
 

Attachments

  • IMG_6637.jpg
    IMG_6637.jpg
    101.1 KB · Views: 89
  • 60736907632__28A55874-216E-41F6-A88C-FD121BA3AED8.jpg
    60736907632__28A55874-216E-41F6-A88C-FD121BA3AED8.jpg
    134.4 KB · Views: 92
  • IMG_6647.jpg
    IMG_6647.jpg
    156.5 KB · Views: 90
  • IMG_6648.jpg
    IMG_6648.jpg
    152.9 KB · Views: 87
  • 60738710826__340C71AB-21BD-4E12-98B7-C6B872CEC10C.jpg
    60738710826__340C71AB-21BD-4E12-98B7-C6B872CEC10C.jpg
    154 KB · Views: 86
  • IMG_6636.jpg
    IMG_6636.jpg
    113 KB · Views: 88
not much done, replaced the bashed up cowl. door jamb was still out of line so I pulled it with some ratchet straps to weld in.
 

Attachments

  • IMG_6698.jpg
    IMG_6698.jpg
    110.3 KB · Views: 34
  • IMG_6697.jpg
    IMG_6697.jpg
    100.4 KB · Views: 31
  • IMG_6695.JPG.jpg
    IMG_6695.JPG.jpg
    96.6 KB · Views: 32
  • IMG_6694.JPG.jpg
    IMG_6694.JPG.jpg
    126.7 KB · Views: 32
  • IMG_6689.JPG.jpg
    IMG_6689.JPG.jpg
    124.6 KB · Views: 32
thanks burg an OI

funny thing, this truck was the last left out of probably 30 at waynes farm, all because of that cowl and door. maybe 10s or even a hundred guys had looked at it, and decided not to buy it because of the cowl. the door hinge I thought was broken was just the pin was worked out and after I soaked it in evaporust it is a tighter hinge than the one I got to replace it.

I guess my point is that no one wanted the truck at any price because of something that was fixed in less than 3 hours. probably a good metaphor for doing something thats been put off because of how ugly or impossible it seems...

happy easter!
 
pedal round 3

attachment.php

attachment.php


this one works nicer, great angles, pedal in right spot, firewall booster mount correct, booster to pedal in line.

but I couldnt get the dash mounts to line up. rather than farking with a "round 4", I decided to see if I could make a dash bracket and bolt it to the pedal bracket. I designed something from memory where the column needs to be

attachment.php

attachment.php


but it held the column to low and too far forward. memory failed me.


so then I tried a new method, a dash bracket that would hold the brake pedal mount in the right position, and would allow me to build the upper column mount.

attachment.php

attachment.php



good so far. had to cut the pedal mount back a little and this first one will need holes drilled, but once I do that I can add it to CAD and the next one will be cut correctly. the pedal mount is angled slightly because I dont have the 5 degree mount installed in the firewall yet.

that worked well so today I popped out the upper column mount, it bolts to the dash bracket and the pedal mount both, not to be a bragger, but if it were a rapper it would be MC Strongasheck.

attachment.php

attachment.php

attachment.php

attachment.php




notice that the center of the column is centered in the gauges, not the old column slot! I little tweak that I love!


so now I just need to tighten all these various brackets and drill the holes in the pedal mount and install the firewall booster mount, and THEN I can design the lower column mount. seems like excessive stuff but on the next truck it will literally take two/two and a half hours to CUT the parts, WELD the parts, and INSTALL the brake pedal and the column, DONE. putting my time in now to work out the bugs!

more coming!
 

Attachments

  • IMG_6751.jpg
    IMG_6751.jpg
    101.2 KB · Views: 49
  • IMG_6752.jpg
    IMG_6752.jpg
    74.5 KB · Views: 48
  • IMG_6777.JPG.jpg
    IMG_6777.JPG.jpg
    85.5 KB · Views: 48
  • IMG_6779.JPG.jpg
    IMG_6779.JPG.jpg
    68 KB · Views: 47
  • IMG_6786.JPG.jpg
    IMG_6786.JPG.jpg
    88.6 KB · Views: 48
  • IMG_6790.JPG-3.jpg
    IMG_6790.JPG-3.jpg
    96.6 KB · Views: 47
  • IMG_6809.JPG.jpg
    IMG_6809.JPG.jpg
    76.2 KB · Views: 46
  • IMG_6812.JPG.jpg
    IMG_6812.JPG.jpg
    97.6 KB · Views: 46
  • IMG_6814.JPG.jpg
    IMG_6814.JPG.jpg
    89.1 KB · Views: 46
  • IMG_6815.JPG.jpg
    IMG_6815.JPG.jpg
    74.5 KB · Views: 47
That's impressive JD.

Crazy that the original columns aren't centered eh? I noticed that with mine and thought - seriously? Mine will be centered as well.
 
Looking good Joedoh. Gotta love a plasma table. It makes life so much easier when you can just knock something like your mount out in house.

Is that 3/16'' plate you're using?[cl[cl[P[P:cool::cool:
 

Latest posts

Back
Top