Rat Rods Rule / Undead Sleds - Hot Rods, Rat Rods, Beaters & Bikes... since 2007!

Go Back   Rat Rods Rule / Undead Sleds - Hot Rods, Rat Rods, Beaters & Bikes... since 2007! > Body... Talk & Q&A

Body... Talk & Q&A Top Chop, Channel & General Body Q&A

Reply
 
Thread Tools Display Modes
  #11  
Old 01-10-2019, 07:39 PM
Neto Neto is offline
Super Member
 
Join Date: May 2012
Location: Holmes Co, Ohio
Posts: 291
Default

Quote:
Originally Posted by sneakysnake View Post
Sounds like its not leaving too many options. Might braze the hole and redrill, be a little softer than welding for drilling and could control the build up.
Yes, I should have thought the whole thing through better before I started in on it. Too anxious to get started on it, I guess. Something will work out, but it does look like I'll need to purchase a 5/16" hand reamer yet. Should have ordered one at the same time I got the bigger one (to share shipping costs). Today I was looking through some of my junk parts boxes, and found one of those threaded lamp pipes. (where the wires go up through) It is just a bit small on the ID, and a bit large on the OD. But just a thin wall tube like that would be difficult to weld in place, at least certainly so for me. I'll also check with a couple of fabrication shops around here, to see if they have a heavy wall tube available already with the correct ID. (I don't have a lathe, either, so if I need to go that route, I will have to hire it done, which kinda' goes against my grain.)
Reply With Quote
  #12  
Old 01-10-2019, 07:56 PM
Dr Crankenstein's Avatar
Dr Crankenstein Dr Crankenstein is online now
Rocket Surgeon
 
Join Date: Mar 2011
Location: SK CAN
Posts: 5,001
Default

I like this alternative...



In my opinion, the guy (on the other forum) had the right idea, but should have used a hard steel instead of a soft copper insert. (How he surrounded the copper sleeve with weld material is beyond me and a "hack" cure at best.)



Anyhow... copper and brass are "sacrificial" and "consumable". You already have the the consumable (wear) bushings pressed into your tongues. I would do what your gut tells you to do... beef up the frame holes, double (or triple) your pin contact area and have a good night's sleep.

.
__________________
- The distinction between psychological illness and creative thinking is wafer thin -

1937 Chevy Coupe
1938 Chevy Sedan
Reply With Quote
  #13  
Old 01-12-2019, 08:41 PM
23crate's Avatar
23crate 23crate is offline
Rusty Rat Rodder
 
Join Date: Sep 2014
Location: new zealand
Posts: 843
Default

way back i remember using gas and bronze rod to fill the eyes in Model A rod brakes .. we then drilled them to suit the new pins. they worked amazingly well..

could you try TIG welding some "silicone bronze" rod and re-drilling?

or even bronzing ?

here in New Zealand there are hinge pin kits for Nissan that come with new pins , circlip and bronze sleeves similar to the one above - Rockauto may have a kit like that ?

crate
__________________
duct tape can't fix stupid, but it can muffle the sound.

the greatest victory is to live
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 05:38 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Rat Rods Rule Inc.