Flash back fairlane

Rat Rods Rule

Help Support Rat Rods Rule:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Got my arms back from coating. Look good!!
 

Attachments

  • 0402192213.jpg
    0402192213.jpg
    88.9 KB · Views: 21
  • 0402192213a.jpg
    0402192213a.jpg
    88.8 KB · Views: 23
Thanks guys, I always want to tower it and make,it handle better in high school. Many years later it is happening. I just got a quote today on everything for a 6 speed swap. If I start savining now by the time I'm dead I can afford one!!

Get the inner front fenders and what not degreased and under coated over the last few days. I will begin the :D
Suspension work this weekend!!!![;)
 

Attachments

  • 0429191638_HDR.jpg
    0429191638_HDR.jpg
    123.8 KB · Views: 20
  • 0430191504_HDR.jpg
    0430191504_HDR.jpg
    119.4 KB · Views: 21
  • 0430191504a_HDR.jpg
    0430191504a_HDR.jpg
    114.5 KB · Views: 16
  • 0429191453_HDR.jpg
    0429191453_HDR.jpg
    123.9 KB · Views: 20
Starting to assemble stuff!!
 

Attachments

  • 0503192220_HDR.jpg
    0503192220_HDR.jpg
    117.6 KB · Views: 10
It has began!
 

Attachments

  • 0504192130a_HDR.jpg
    0504192130a_HDR.jpg
    103.6 KB · Views: 10
  • 0504192130_HDR.jpg
    0504192130_HDR.jpg
    135.1 KB · Views: 10
  • 0504192215b_HDR.jpg
    0504192215b_HDR.jpg
    114 KB · Views: 10
  • 0504192215_HDR.jpg
    0504192215_HDR.jpg
    115.6 KB · Views: 11
  • 0504192223_HDR.jpg
    0504192223_HDR.jpg
    117.8 KB · Views: 11
Started cleaning the frame on the underside so I can undercoat it. Also got some parts assembled and readt for installation
 

Attachments

  • 0506192118_HDR.jpg
    0506192118_HDR.jpg
    183.8 KB · Views: 12
  • 0506192110a_HDR.jpg
    0506192110a_HDR.jpg
    128.2 KB · Views: 11
  • 0506192101a_HDR.jpg
    0506192101a_HDR.jpg
    115.8 KB · Views: 12
  • 0506192110_HDR.jpg
    0506192110_HDR.jpg
    129.1 KB · Views: 11
Forging ahead full steam.... [cl [P Are you having the powder coat done or doing it in house? At least the small stuff...?
 
Got some parts installed. Lots of work still but a step in the right direction
 

Attachments

  • 0507191812_HDR.jpg
    0507191812_HDR.jpg
    121.3 KB · Views: 15
  • 0507191809_HDR.jpg
    0507191809_HDR.jpg
    58 KB · Views: 13
  • 0507191808_HDR.jpg
    0507191808_HDR.jpg
    105.6 KB · Views: 15
  • 0507191807_HDR.jpg
    0507191807_HDR.jpg
    122.1 KB · Views: 14
  • 0507191807a_HDR.jpg
    0507191807a_HDR.jpg
    137.1 KB · Views: 15
Sitting on its own weight
It's not done by any means but I need the lift for another project. I did order my competition engineering adjustable strut rods. They should be here by the end of the month. Then I need shocks and brakes then we will move on to the rear end
 

Attachments

  • 0512191721_HDR.jpg
    0512191721_HDR.jpg
    164.4 KB · Views: 31
  • 0512191721a_HDR.jpg
    0512191721a_HDR.jpg
    167 KB · Views: 31
  • 0512191722_HDR.jpg
    0512191722_HDR.jpg
    156.4 KB · Views: 23
Got my adjustable strut rods on today
 

Attachments

  • 0527191542_HDR.jpg
    0527191542_HDR.jpg
    96.8 KB · Views: 23
Hehehehehe[cl[dr[;):D
 

Attachments

  • 0528191631_HDR.jpg
    0528191631_HDR.jpg
    76.9 KB · Views: 16
  • 0528191634_HDR.jpg
    0528191634_HDR.jpg
    76.7 KB · Views: 16
  • 0528191634a_HDR.jpg
    0528191634a_HDR.jpg
    135.9 KB · Views: 17
So after banging my head against the side of that F100 we are building and and my oil pressure issues with it I decided to roll it outside on Friday afternoon and drive in the old Fairlane. Quickly we had the old rear leaf springs removed and we're installing bracketry for the new four- link. My homework proved to be correct in the fact that these 66-67 Fairlane run the same back half as the 68 69. So all of my link brackets and links went on to the car with ease and about two and a half hours later I had my 4-link mocked up under the car and was able to set it down and take a look at the stance. The front end will now be going down a little bit lower because this is how I wanted the car to sit when I started this. Next Friday hopefully I will get it on a lift in the afternoon and I will pull the whole suspension out from underneath of it and fully weld everything
 

Attachments

  • 0531192237_HDR.jpg
    0531192237_HDR.jpg
    110.3 KB · Views: 21
  • 0531192237a_HDR.jpg
    0531192237a_HDR.jpg
    99.4 KB · Views: 21
  • 0531192237b_HDR.jpg
    0531192237b_HDR.jpg
    135.4 KB · Views: 18
  • 0531192238a_HDR.jpg
    0531192238a_HDR.jpg
    115.5 KB · Views: 18
  • 0531192235a_HDR.jpg
    0531192235a_HDR.jpg
    120.7 KB · Views: 18
  • 0601191554_HDR.jpg
    0601191554_HDR.jpg
    174.4 KB · Views: 18
I've not seen an upper bracket mounted on the front of the axle housing before.
Does it make any difference whether it's on top or on the front?
 
I've not seen an upper bracket mounted on the front of the axle housing before.
Does it make any difference whether it's on top or on the front?

I never had either but all of their bolt in kits they self are like that. I honestly don't think it'll make a difference because you still have good separation between the two top and bottom links. I guess we'll find out
 

Latest posts

Back
Top