My 71 C10

bjsmith0098 · Nov 13, 2011

all of these post are from another forum i have it posted on just thought i would do one here to and will be lots of pics i know everyone like pics. picked up 71 c10 about a year ago plans were to lower and install 6.0 but few weeks ago i picked up 5.3 with computer and harness for $300 so decided to do turbo setup
this is when i picked up the truck

options

washed it up

removed front cap and bed

removed springs to decide about where i want ride height

bjsmith0098 · Nov 13, 2011

notched frame

test fit 5.3

tacked engine mounts in

started plating them in the engine came with frame mounts out of z71

bjsmith0098 · Nov 13, 2011

removed cab

finished washing frame

replaced rusted cab corners common problem with these trucks

shaved marker lights on bed

also shaved them on front fenders,welded upi most of the holes for mounting trim, and filled stake pockets on bed
front fenders

got frame primed may leave it that way did lil body work where my welds are, also ordered all new ball joints, tie rods, and a-arm shafts still need to get new wheel bearings and drop spindles

picked up new fuel tank on craigslist and installed to get rid of tank from behind seat

bjsmith0098 · Nov 13, 2011

got few mor things don new fuel tank, all new front suspension parts, got engine and trans set in place. also got turbo in and ordered bags for it

got front bags mounted now just need my drop spindles

bjsmith0098 · Nov 13, 2011

ot the rears done today

all the way down no air front will be lower when i get drop spindles

all the way up

about where it will ride at

got the bottom of bed primed yesterday and installed it today

redneck bed lift

no air

aired up all the way

ride height

bjsmith0098 · Nov 13, 2011

got the ac compressor mounted had to bend frame down a lil to clear hoses also have lots of parts on there way

also got few parts in today
going to paint drop spindles before installing

radiator

intercooler

got more parts 02 zo6 cam, walbro 255, tail bov, areomotive fpr with boost reference,60lb injecters, 3x4 coupler for turbo pipe to throttle body

fuel pump mounted

got one side of bed primed and spindles painted

bjsmith0098 · Nov 13, 2011

thinking of mounting coils like this but will have to see how i have to run exhaust as it will be 3.5" because i can get most it from work

got more parts tial wastegate,wideband 02,egt gauge, turbo flange, check valve kit for th350 vacuum modulator,2 14" spal fans

got intercooler pipeing in

got other side of bed primed and back

bjsmith0098 · Nov 13, 2011

primed underside of cab and the back of it

started redoing wiring harness

removed wires not needed was alot

extra pins removed from ecm

how it looks now every wire in harness will be made longer or shorter to route wires where i want them

still have some body work to do on bed but easier to see when its one color

bjsmith0098 · Nov 13, 2011

finally got my spindles installed but will be replacing bearings and rotors later on

gets alot lower now

got new injectors in along with new pigtails for them and turned them to inside to clean up the wiring because coil packs will not be on valve covers and alt,throttle body wiring will be under intake

started to fit hydro boost only had to dril couple holes and will have to extend the rod that connects to brake pedal

started to rattle can firewall but ran out of paint

bjsmith0098 · Nov 13, 2011

finished up firewall and painted back of cab and front of bed with rattle can so when new mounts come in i can put cab back on. paint is valspar low gloss black tractor paint from tractor supply back of cab still wet so looks more glossy than it is

got new 3k stall transmission specialties converter in

got more wiring done today and finaly decide where to put coil packs just have to make custom brackets and plug wires

it been a while had lots going on and no time to do stuff to truck but did finally get the cab on, front fenders and hood mocked up to get idea of what its going to look like. this is sitting at ride height

layed out

bjsmith0098 · Nov 13, 2011

got some exhaust work done last couple days cut and welded stock manifolds they are cast but didn't heat or anything and welded good with no cracks now i just need to get some bends to finish it up then take the time to smooth everything out before i have them coated

finally got turbo mocked up in place hope to do more soon

few more pics from this morning. got intercooler in just need to finish top mounts. had to see how it would look behind the grill that will eventually be black

Sam_Fear · Nov 13, 2011

Wow! [dr

hankus · Nov 13, 2011

Thats gonna be a bad truck

hotrod preacher · Nov 13, 2011

looking good....anxious to see more[P[P

bjsmith0098 · Nov 13, 2011

thanks and it should have about 600 hp to the wheels when its done. its going to be satin black when done. its no rat rod to me but is a hot rod. some would say it is a rat rod just because the color but i just thought some of you would like to see the build. im trying to find me a rat rod now but have to sell my boat to get one i was trying to trade for this one but the guy didnt want my boat but its something like im looking for a chop top

38fordtruck · Nov 13, 2011

Sam_Fear said:
Wow! [dr

+1[P[cl

ShovelHeadShawn · Nov 13, 2011

good looking build. cant wait to see more

OldKarznTruckz · Nov 13, 2011

Very nice!

Tyster36 · Nov 13, 2011

For sure on the more of a hot rod. Great build! Ought to scoot along pretty good when your done

Bonehead · Nov 13, 2011

Nice build no matter what you call it.

My 71 C10

Help Support Rat Rods Rule:

Member

Member

Member

Member

Member

Member

Member

Member

Member

Member

Member

Brother Rat

Well-known member

"Official RRR Chaplain"

Member

Well-known member

Well-known member

Active member

Well-known member

Skull Master

Similar threads

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!