Undead Sleds / Rat Rods Rule - Hot Rods, Rat Rods, Sleepers, Beaters & Bikes... since 2007!

Go Back   Undead Sleds / Rat Rods Rule - Hot Rods, Rat Rods, Sleepers, Beaters & Bikes... since 2007! > Builds!

Builds! Post your project here... show us what you're up to! Please Note: This section is for "Builds" ONLY!

Reply
 
Thread Tools Display Modes
  #61  
Old 07-29-2021, 08:31 PM
Skip's Avatar
Skip Skip is offline
Rusty Rat Rodder
 
Join Date: Jun 2010
Location: Portland, OR
Posts: 3,644
Default

Well, here we go. Sitting on an idea for a couple weeks can make a fella change his mind and turn the idea completely upside down. The new visor idea. It will get a bit more sculpting on the leading edge, but I think this is the way it will be.
Attached Images
File Type: jpg Visor1_sm.jpg (83.2 KB, 32 views)
File Type: jpg visor2_sm.jpg (88.4 KB, 27 views)
File Type: jpg visor3.jpg (79.8 KB, 24 views)
File Type: jpg visor4.jpg (62.2 KB, 29 views)
File Type: jpg visor5.jpg (63.9 KB, 23 views)
File Type: jpg visor6.jpg (67.4 KB, 27 views)
__________________
39 Ford PU Build. http://ratrodsrule.com/forum/showthread.php?t=36459
1928 Ford Tudor Build http://ratrodsrule.com/forum/showthread.php?p=538231#post538231
The thing about a '39 Ford pick-up is that that ugly grille kinda' grows on ya' after a while.

Not taking anything too seriously.
Reply With Quote
  #62  
Old 07-29-2021, 08:55 PM
Skip's Avatar
Skip Skip is offline
Rusty Rat Rodder
 
Join Date: Jun 2010
Location: Portland, OR
Posts: 3,644
Default

I have also found a few other pieces of the puzzle. Mostly little stuff. The little stuff that costs an arm and a leg most often. As I do not want to have a gas tank sitting right in my lap, I was going to cut the original tank. But on inspection, it is so nice, I just couldn't do it. Some restorer will want it. Thus, when another less than perfect tank showed up on CL less than an hour away, I was on it. Lucky for me, the gentleman that was selling it is working on a couple 30/31 model As. A Vicky and a Coupe. So, we made a trade. His tank for the NOS windshield side trim pieces that I got on eBay with the ones i needed for my sedan. We were both happy and parted feeling like we got the best part of the deal. The tank was really heavy. Way heavier than it should have been. When I took the cutting wheel to it, it stank like dead critters. Turned out if was half full of a rodent next. Anyway, it cleaned up real nice.


Next (well soon anyway) will be designing a dash that will hold two 3-1/8 inch gauges, and six 2-inch gauges. And it can not look like a 32 dash. And preferably, it will not look like anyone else's dash. But it will rock! I have a couple ideas churning in my little pea brain. This train of thought is due to a killer deal on eBay for the tach that matches the set I already have. I had pretty much written off having a tach, just because the matching unit was over $160, and I really don't need a tach. But they are cool.
Attached Images
File Type: jpg cowltop1.jpg (66.0 KB, 23 views)
File Type: jpg cowltop2.jpg (60.5 KB, 23 views)
File Type: jpg cowltop3.jpg (58.7 KB, 23 views)
File Type: jpg cowltop4.jpg (59.6 KB, 20 views)
File Type: jpg cowltop5.jpg (56.7 KB, 21 views)
File Type: jpg cowltop6.jpg (64.7 KB, 22 views)
__________________
39 Ford PU Build. http://ratrodsrule.com/forum/showthread.php?t=36459
1928 Ford Tudor Build http://ratrodsrule.com/forum/showthread.php?p=538231#post538231
The thing about a '39 Ford pick-up is that that ugly grille kinda' grows on ya' after a while.

Not taking anything too seriously.
Reply With Quote
  #63  
Old 07-29-2021, 09:14 PM
Old Iron's Avatar
Old Iron Old Iron is offline
Rusty Rat Rodder
 
Join Date: May 2011
Location: Willard Mo.
Posts: 13,718
Default


Reply With Quote
  #64  
Old 07-29-2021, 09:41 PM
Torchie's Avatar
Torchie Torchie is offline
Rusty Rat Rodder
 
Join Date: Mar 2013
Location: Northern Michigan
Posts: 7,636
Default

Quote:
Originally Posted by Old Iron View Post

^^^^^^^Xs 2 ^^^^^^
Torchie
Reply With Quote
  #65  
Old 08-05-2021, 12:41 PM
Skip's Avatar
Skip Skip is offline
Rusty Rat Rodder
 
Join Date: Jun 2010
Location: Portland, OR
Posts: 3,644
Default

There has to be something wrong here. Ten feet away from this pile of rust is a nice insulated shop with almost everything a feller would like or need to work on this project, yet here I am working outside under a tree.

Anyhoo, I scored a hood Tuesday afternoon. so I had to try it on to see if I even liked the look. The hood is rough, which is appropriate for the project. wouldn't want to waste any nice parts on it. Right? But it is very fixable. It cost too much money for something that would have gone to the scrap pile a few short decades ago. Such is the way of the hobby.

i also pulled out the grilles I bought on on eBay. A Speedway 28, and a 32 from some upstart company. I tried them both on. Now i have no doubt which grill I will use.

This thing sure got "long" with a hood and grille on it.
Attached Images
File Type: jpg Awith32grille1.jpg (69.2 KB, 21 views)
File Type: jpg 28grille.jpg (77.6 KB, 24 views)
File Type: jpg 28_side.jpg (48.9 KB, 23 views)
File Type: jpg hood2_sm.jpg (53.3 KB, 23 views)
File Type: jpg hoodside1sm.jpg (47.4 KB, 23 views)
__________________
39 Ford PU Build. http://ratrodsrule.com/forum/showthread.php?t=36459
1928 Ford Tudor Build http://ratrodsrule.com/forum/showthread.php?p=538231#post538231
The thing about a '39 Ford pick-up is that that ugly grille kinda' grows on ya' after a while.

Not taking anything too seriously.
Reply With Quote
  #66  
Old 08-05-2021, 03:45 PM
05snopro440's Avatar
05snopro440 05snopro440 is offline
Rusty Rat Rodder
 
Join Date: Sep 2012
Location: Sherwood Park, Alberta
Posts: 4,057
Default

Quote:
Originally Posted by Skip View Post
There has to be something wrong here. Ten feet away from this pile of rust is a nice insulated shop with almost everything a feller would like or need to work on this project, yet here I am working outside under a tree.

Anyhoo, I scored a hood Tuesday afternoon. so I had to try it on to see if I even liked the look. The hood is rough, which is appropriate for the project. wouldn't want to waste any nice parts on it. Right? But it is very fixable. It cost too much money for something that would have gone to the scrap pile a few short decades ago. Such is the way of the hobby.

i also pulled out the grilles I bought on on eBay. A Speedway 28, and a 32 from some upstart company. I tried them both on. Now i have no doubt which grill I will use.

This thing sure got "long" with a hood and grille on it.
28-29's just look wrong with a 32 grille, but that's just my opinion.
__________________
My 455 Buick powered '46 GMC Build Thread

My '46 GMC on Photobucket
---------------------------------------------------------------
When you don't know what you're doing, it's best to do it quickly.

And when Im gone, you can call me foolish but hopefully not boring. I will have lived.

The more I learn about women, the more I like my car.
Reply With Quote
  #67  
Old 08-05-2021, 06:13 PM
Torchie's Avatar
Torchie Torchie is offline
Rusty Rat Rodder
 
Join Date: Mar 2013
Location: Northern Michigan
Posts: 7,636
Default



Torchie
Reply With Quote
  #68  
Old 08-05-2021, 07:49 PM
Skip's Avatar
Skip Skip is offline
Rusty Rat Rodder
 
Join Date: Jun 2010
Location: Portland, OR
Posts: 3,644
Default

Quote:
Originally Posted by 05snopro440 View Post
28-29's just look wrong with a 32 grille, but that's just my opinion.
Well, Sir, that makes three of us that agree on this matter. You, me, and the Good Doctor.

I got two of the hood hinge pins out this afternoon. WD and a long 1/4-inch stainless rod. The center pin is a tube, and I am still trying to figure out how to get it out. In the mean time, I'm letting the WD do its thing. Funny part was that after I drove the first pin out, I couldn't figure out why the parts didn't come apart. Then I noticed the drive pin. After I removed the "tool" the side came right off no problem.


Does anyone have experience with the center hinge pin on a 28/29 hood?
__________________
39 Ford PU Build. http://ratrodsrule.com/forum/showthread.php?t=36459
1928 Ford Tudor Build http://ratrodsrule.com/forum/showthread.php?p=538231#post538231
The thing about a '39 Ford pick-up is that that ugly grille kinda' grows on ya' after a while.

Not taking anything too seriously.
Reply With Quote
  #69  
Old 09-04-2021, 07:55 PM
Skip's Avatar
Skip Skip is offline
Rusty Rat Rodder
 
Join Date: Jun 2010
Location: Portland, OR
Posts: 3,644
Default

I ended up making a tool to fit inside the center hinge pin tube. Then I clamped onto it with a pair of vice grips and beat it out. No harm to the hood panels. The pin isn't much worse off than it already was. I can order new pins if I decide to use all or part of the hood.

I've been hunting for window frame pieces, and have come to the conclusion that to get all the little pieces will cost more than I am willing to invest. Some I can make, but the real question is, do I really need them to start with? What else can I do? Now I really love panel trucks, and sedan deliveries. So, I looked at a bunch of real ones, and different conversions on Google. So many variations. Some nice, some just look like no real thinking was involved. Then there is the issue of me sitting essentially behind the B-pillar when I am wedged into the beast. So, how about a smallish window and fill the rest of the side panels. I played around in PhotoChop for a while, and it looks like it will work. If I can decide which part of the belt line and "hook" behind the quarter window to move, and where. More options. I was also having trouble deciding on how big the little quarter window should be, and how to shape it. Well maybe that is sorted out. I just bid too much on a pair of window garnish molding for a 28/9 coupe. If I win, I will know the shape and size of the new quarter windows. The other window that needs addressing is the back window. The garnish for the back is more than I just bid on the two quarter window pieces. But, over in the parts bin is a very nice 38 ford PU window garnish, and the cab out in the yard is scheduled to be turned onto a RPU, so there is the outer skin. Its a little wider, and a lot shorter, and not what everyone else has. That has great appeal to me.

When I wake up Monday morning, I'll know if coupe windows are the new order of the day.

The mini-mill is set up and ready to go to work, so I believe I will make some door hinge parts. All I need now is some accurate measurements. These are the towers that attach to the side of the A-pillar. It looks like the two top hinge pieces are the same "height" (actually, the distance from the A-pillar to the outside end of the hinge). So I have an example for the center hinge. Does anyone have a 28/9 sitting around that they can take a measurement of the bottom hinge for me? It would be greatly appreciated.
__________________
39 Ford PU Build. http://ratrodsrule.com/forum/showthread.php?t=36459
1928 Ford Tudor Build http://ratrodsrule.com/forum/showthread.php?p=538231#post538231
The thing about a '39 Ford pick-up is that that ugly grille kinda' grows on ya' after a while.

Not taking anything too seriously.
Reply With Quote
  #70  
Old 09-04-2021, 08:46 PM
Torchie's Avatar
Torchie Torchie is offline
Rusty Rat Rodder
 
Join Date: Mar 2013
Location: Northern Michigan
Posts: 7,636
Default

Wheres the pics of your photochop ideas? We want to all add our 2 cents.😂
I feel your pain on the window frames, Skip.
Pieces like that really drive up the costs of a build.
My car came with most of the belt line trim missing. I have the ones for the doors but the two piece trim that wraps around under the rear window and up to the door openings is missing.
I found one on eBay. $400 plus shipping. Ouch. I will use the one from my donor 4 door and add to the length with the ones from its rear doors.
I will make a wedding band to cover the seems.
Torchie
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 05:41 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
Rat Rods Rule Inc.