Willys long cab
- Thread starter I-R-POPS
- Start date
Help Support Rat Rods Rule:
I-R-POPS
''Rusty Mopar Slacker''
Thanks Joe.
I-R-POPS
''Rusty Mopar Slacker''
I-R-POPS
''Rusty Mopar Slacker''
soltz
The Rat Captain
One up or one down [S
Good luck with it [P
Good luck with it [P
kenny c
Well-known member
[S[S
Is there a way to clock the transfer case? Could you use a different trans and maybe a divorced transfer case? How about rotating the key a the end of the torsion out of the way and build another anchor?
Is there a way to clock the transfer case? Could you use a different trans and maybe a divorced transfer case? How about rotating the key a the end of the torsion out of the way and build another anchor?
DozerII
Well-known member
Wow that really sucks. That's what I was thinking Kenny rotate the torsion bar adjuster down out of the way[S[S
kenny c
Well-known member
If it can be done maybe move it 90 degrees so that the adjuster screw is parallel with the ground.[P
Torchie
Well-known member
[P [P [P [P [P
Torchie
Torchie
Old Iron
Well-known member
Cut the cross member off and lower it two inches.
I-R-POPS
''Rusty Mopar Slacker''
I-R-POPS
''Rusty Mopar Slacker''
Thanks for the brain storming guys.
Me being me I've got to use the transmission that I built and it has to be where where it has to be to work. After I get the motor and transmission mounts in place then I'll deal with the issue of the torsion bar.
My dear old dad used to tell me if it was easy any one could do it.
Me being me I've got to use the transmission that I built and it has to be where where it has to be to work. After I get the motor and transmission mounts in place then I'll deal with the issue of the torsion bar.
My dear old dad used to tell me if it was easy any one could do it.
soltz
The Rat Captain
Rest assured your not the first or last that has/will bleed for a project
Rest well, you'll have time to think about the problem [cl
Rest well, you'll have time to think about the problem [cl
Skip
Well-known member
I did that with a sawsall. (slightly different location) I told the doc to give me a Frankenstein scar so I don't forget again. Glad you are OK.
- Joined
- Nov 5, 2015
- Messages
- 3,225
smallfoot
He's rockin' the "Nuttin Special"!
Your floors , like most of ours, would be marked as a crime scene if they ever did an investigation of all the blood stains on the floors! That cut's position is going to make it a little painful using that hand for a minute or two. We all do it but be careful...
Old Iron
Well-known member
^^^X2^^^
Torchie
Well-known member
once in a while I need to do something stupid like that to keep me focussed....
Like a laser I am.
[dddI stopped counting stitches at 350 and that was before they started cutting things off of me.[ddd
Sending you healing vibes, POPS.
Torchie
05snopro440
Well-known member
Holy! That's a good one.
We've all done stupid stuff like that when we weren't paying quite enough attention. In 2018 I cut halfway through the end of my thumb with brand new battery powered hedge clippers. They were nice and sharp.
Take a rest and heal up!
We've all done stupid stuff like that when we weren't paying quite enough attention. In 2018 I cut halfway through the end of my thumb with brand new battery powered hedge clippers. They were nice and sharp.
Take a rest and heal up!
bob w
Still crazy after all these years!
Ouch! Don't do that anymore.
