Search results

Just in case any of you guys close to the Gulf Coast aren't paying attention, we're throwing a hurricane. Due to come close to me early in the morning. We're hunkered down waiting.

I have a large upright air compressor that is very top-heavy. I am moving in the next couple of months and need to move it about 200 miles. Would there be any problem with laying it down to haul on a trailer? Thanks in advance.

Have any of you guys used any of the aluminum rods that a being advertised on Facebook? The ones you use a propane torch with? They look too good to be true.

I know this may stupid but there a simple way to tell a sbc intake from a bbc when you have a motor or another intake to compare it too.

Traveling back from helping my Son move to Montana. Are there any car shows or swap meets in Wyoming, Colorado or Oklahoma coming up this coming weekend? Also any interesting car stuff between Montana and Alabama.

What do I need to make led lights flash properly for turn signal?

Made what I hope is a good score today. I acquired a 60's 300hp 327 with 400 trans. The guy also had a complete 55 265, 4 350's, a 283 and 2 305's that that had all been in storage for years.

There is a store here in Fairhope similar to a Western Auto that has been closed for years. Still a lot of stock on the shelves. It's now being sold. A few things that might be of interest to some of you guys. A good many 6v headlight bulbs old starters and a few 30's distributors new in the...

Anybody ever use a gps speedometer that looks like a regular round in dash speedometer? I saw them on amazon. Not too expensive.

I got my new windshield for the "Salvage #1" 55 Studebaker pickup. I'm not sure where to start. Do I put the rubber on the windshield first or on the truck opening first? Does it go in from the inside or outside? Top or bottom first? I've been told to use a rope and have seen that done many...

Finally got around to starting a build thread, with the help of my sweet wife. I'm building a rat rod pickup/bobber, using a '55 Studebaker pickup cab. All of my engine and running gear will be Chevrolet. I have a Ford Model A grill shell and I'm using the Studebaker straight axle, which has...

Can anyone tell me if a 4cly from a 94-97 s10 is non computer engine? Can it be changed to a carburetor? Is it anything like the older "Iron Duke" engine. I got a chance get one and a t-5 transmission pretty cheap. Was considering it for a project for my grandson in a Geo Tracker. Thanks

I've been a member here for a year or so and I'm ready to start a build thread. The problem is I haven't got a clue how to post pictures . My sweet wife is the tech person in the family and will help. I just need some of you guys to explain how she can get started. Thanks in advance for helping...

Where is the best place to get glass for 55 Studebaker pickup?

Anybody going to the Moultrie swap meet next weekend?

You guys may already know this but I'll throw it out anyway. If you need sheet metal for floors or whatever I found a good source. Most hvac companies have junk ac units that have a lot of good sheet metal especially the big commercial units. It's a good thickness and painted on both sides and...

What do you guys that have parts washer use for solvent. I have a older safety clean washer that I bought at an auction. I have used kerosene in the past but can't find it for less than $45.00 for five gallons since I moved to south Al. Last I bought about 2 years ago was 6.00 a gal. I have...

Has anyone tried using spray in bed liner on the overhead (ceiling) of a truck cab or car? It seems it could be an option. Phil Cottingham

Is there a good rat rod magazine out there?

I have a rear end from an 85 el camino that I plan to use in my build. It has 4arms connected to the frame. Is there any reason I can't use these mounting points on the rear housing and there same angles for mounting to my new frame? I plan to use the el camino coil springs as well. The frame...