Search results

Don't understand how that works? Does oil flow to the canteen?

Thanks Bob. I'm pretty happy with stance. Was trying to get the Graboski rake.:D

[cl Got it running and drove it outside then down the driveway, that's about 300 yards. First thing I didn't like was the windshield too tall, my line of sight is right into the top bar. I may get used to it or could cut it off. Goes in gear hard, only idles at 650 but may need a higher...

progress Got the headers built, mufflers attached. Painted with high temp paint, we'll have to see how that holds up. Madea step under the doors to keep from burning my leg and a bracket to support the weight. Should be ready to start it up tomorrow.

Yeah but due to health issues this will probably be the last one. It's much harder working on this stuff at 81 yrs than it was 40 years ago..lol

Been a long time since I posted but while waiting for my transmission to come back from the shop I installed tail and tag lights and finished all the wiring. Had to mount turn signal switch on the floor cuz I don't have a steering column. Use the tach for speedometer. Got trans back and set in...

Title as home made..

Some reason pics didn't show up, try again

Got a little more done. Mounted fuel tank, pump and lines installed. Mounted simulated bed, actually had to do it over cuz my original mounts were crooked. That happens when u only got one eye, also makes welding difficult. Got confidence in my welds they just not too pretty.:(

Got a few things done. Made seat and covered with Chinese blanket. Mounted Camaro shifter with safety switch. Made gas pedal , mounted it and made foot rest cuz its over the trans hump. Finished steering shaft, two u joints and two supports, sits high cuz need room for my big self. Installed...

Interior door hinges for houses! ,bear claw latches. Steering box is Ebay Corvair copy, used em before and seem pretty good for the price, $175. Will keep updating...

How you doing Bob? .. Short box is built just waiting to finish fuel lines and wiring. 383 Small block chevy, finished , hanging on engine stand.

Built frame from 1 1/2 x 3 tube, longer than most T's, 110 inches . Wider also , Exolorer rear, parallel 4 link, coil overs. Ron Pope front axle. Started with a 23 T cowl but built the rest of the body from scraps laying around. Bit wider and longer than average T. I'm longer and wider than...

Why not do the same mount on front as u did on the rear?. One short bar will cause the axle to roll as it travels up and down. [not very much but it will, prolly won't matter that much anyway] If you're going to autocross or off road you'll want watts linkage on front, if u going to just cruise...

Our government is a terrorist organization. Hundred years we didn't need a permit to catch rain water. Today the police state busts children for a lemon aid stand. We are much too afraid of the "man" it has destroyed our creativeness. Sorry about the rant,it's the anarchist in me. Have...

My other car has side exhaust and little "Nerf" bars to protect the legs. Guess I'll do the same on this one.

There's no room for the typical fenderwell exhaust. The only ready made headers are by Patriot and once installed you can't change plugs or do a compression check. And the drivers side exhaust pipe would have to be too close to transmission, so I made my own.

This v8 s10 I'm building doesn't have much room for exhaust so I built my headers to exit thru the fenders. Now I can't make up my mind where to rout the pipes. Thought I might go over the roof to be different but kinda not sure now. I routed the drivers side pipes like traditional side pipes...

Call them trolls or whatever. I think some people with nothing better to do are posting ads like this. I see more on Face Book market place with out outrageous prices and If you respond you never get an answer..[S

Tripper..here's a link to the kit I installed. https://www.ebay.com/itm/700-R4-4L60-2004R-HP-4th-gear-only-Lock-up-Kit/250782490166?hash=item3a63cd1e36:m:my5bfIXbwkqAPZNf-oY73eQ