I hear ya there Sgt. Pretty soon it will be the CBCR. The "Coach Built Cruisers Rule" board!
Chevy/Reo?
- Thread starter bob w
- Start date
Help Support Rat Rods Rule:
I hear ya there Sgt. Pretty soon it will be the CBCR. The "Coach Built Cruisers Rule" board!
bob w
Still crazy after all these years!
Made the front shock mounts. Still have to trim the frame covers so I can weld them in place.
Also trimmed the original spring pads off the axle and made 1" lowering blocks for the front.
You guys stop teasing me about "coach built", "raising the bar", etc. The fit and finish of this build in no way compares to many other build threads here. You skill guys know who you are... I am pretty happy with the lines and proportions of the thing. It is close to what I had in mind. As long as it looks, it is only a 103" wheelbase.
ronnysplymouth
Well-known member
Every mod you make on this thing makes it look more and more killer......
bob w
Still crazy after all these years!
Had to notch the frame for front axle clearance.
bob w
Still crazy after all these years!
I trimmed the front frame covers to clear the shock mounts and the semi-circular cutouts for axle clearance.
Added a second bearing on the steering shaft, at the firewall. The other bearing is at the dashboard. The little plate slides up and down with the bearing when adjusting steering wheel height and covers the oblong hole that permits the adjustment. It is crooked in the pic but will be straight in final assembly.
I was putting a drop in the tie rod to clear the front crank pulley when I ran out of MIG wire. Waiting for the radiator.
bob w
Still crazy after all these years!
Got the dropped tie rod finished. Only drawback to them is setting toe in. The tie rod end must make a full revolution when adjusting.
Trimmed the motor mounts so they don't look so bulky. That required adding some rectangular tubing to the inside of the frame rails.
Thinking one, two or three beads might look good on the frame covers (see tape). Any opinions?
If there is a Photoshop guru out there I'd be interested in seeing a pinstripe border around the frame cover. About an inch or inch and a half in from the edge.
sawzall
Well-known member
This rod is so damn cool, I think the 2 beads on the frame cover looks just right if they are going to be the size of the tape, If you make them narrower 3 would be good. What wheels and tires are you thinking of running?
GJunktionMike
Something's wrong with that boy!
agreed
Old Iron
Well-known member
I really like the frame covers too
Hadn't thought of that myself
Hadn't thought of that myself
bob w
Still crazy after all these years!
The radiator arrived complete with chop sticks and sticky rice. It's designed for a chopped '32 Ford shell and fits well in my application. Made mounting brackets for it with it sitting on a rubber pad made from a bed mat. Dropped it off at Tator's to have the bottom outlet messaged to clear the axle.
I used a 3M paint stripper wheel and some phosphoric Prep & Etch and removed some rust from the body. Thinking of running it in bare metal the first year. I've heard Evaporust works very well so I'll try that. Will have the inside of the cab sand blasted but I don't want the sandblasted look on the exterior.
A while back I got a set of 16" Dodge artillery wheels. Hoping to use those. They're narrow so I'm not sure if I can get a 30" or 31" tire on them for the rear. The car needs tall rear tires to attain a rubber rake as I didn't build enough rake into the chassis.
Dirtyrat
Got Fins?
I think the beads will look good as laid out above...
shakey56
Well-known member
Tires
Hey Bob. Look at an 85 series tire. That's what I plan to run on Buford. I have measured a 235 85R16. It is 31" tall. You might want a skinnier tire. They come in a lot of widths. I just think I need a wide tire for the front on Buford...big, big truck, you know. But....check em out.....might be what you're looking for.
Lynn
Hey Bob. Look at an 85 series tire. That's what I plan to run on Buford. I have measured a 235 85R16. It is 31" tall. You might want a skinnier tire. They come in a lot of widths. I just think I need a wide tire for the front on Buford...big, big truck, you know. But....check em out.....might be what you're looking for.
Lynn
bob w
Still crazy after all these years!
Is there a RRR member that could cut the REO letters as shown in the pic with waterjet, laser, plasma or whatever? Probably 14 ga. steel.
This is a cash job, not looking for charity.
Thanks for the tire information guys. I would like to avoid Coker on this project. Have bought lots of tires from them and have had no problems. Just don't want to spend that much this time. Unfortunately, I think this thing needs bias tires.
I agree two beads on the frame covers is good. I'll have to see if Terry & Lee will fire up the Pullmax.
Terry did a great job changing the bottom outlet on the radiator. Unfortunately it didn't buy me enough room so I had to move the axle rearward an inch. That of course means other finished items needed to be changed. So I've been in "rework" mode today.
shakey56
Well-known member
tires
Bob, I understand about the tire price. The 85 series tire is available thru many manufacturers. You can get them thru a local dealer. You dont have to go to Coker. Just clarifying....
Lynn
Bob, I understand about the tire price. The 85 series tire is available thru many manufacturers. You can get them thru a local dealer. You dont have to go to Coker. Just clarifying....
Lynn
Sunnybeach
Well-known member
I found a better image of the REO logo:
And started the first step of converting it to vector format (for plasma/laser cutting):
Question, how big to you plan to make this thing? Essentially, how perfect does the art need to be?
I will spend some more time working on this tomorrow night unless someone can find a vector version of the logo that already exists.
And started the first step of converting it to vector format (for plasma/laser cutting):
Question, how big to you plan to make this thing? Essentially, how perfect does the art need to be?
I will spend some more time working on this tomorrow night unless someone can find a vector version of the logo that already exists.
Attachments
I can do it easy for you, but you may want to try and find someone closer first LOL...
Bob, I can cut it with a CNC plasma. If the other member can turn it into a .DXF file then it would be a breeze. I think I have a left over chunk of 1/8" (11 ga) that will cover it depending on the size. i would only hit you up for shipping as the material is already paid for and the other member did the hard work of converting it to .DXF
