28 Fast Four build

[Burgerman]

Sure like the running board Dozer.

 

[joedoh]

running boards look sharp[cl

 

[DozerII]

Thanks Guys

 

[DozerII]

Sooo after our pre-Christmas postal strike some of my parts orders are trickling in.

My air ride control kit with compressor, and 3 gallon air tank..

Cooper Cobra GT's i actually got the best deal shopping local at our little tire shop. 215 70R15 front and 255 70R15 rear. I have Wheel Viniques 14 series Gennie wheels on order so just using a set of Exploder wheels on the rear as they have the correct offset and they were laying in the scrap pile.

 

[DozerII]

Advice and opinions

After bending up the new running boards I needed to install the front fenders to line everything up for the mounting holes for the boards. Then I did a major clean on the shop and got the car turned for a profile shot.
I'm thinking the rad shell needs to drop a little to follow the rake, thoughts? Anything else looking like it is out of wack?

And a shot from the rear.

 

[Burgerman]

Nice profile look. How much room do you have up front to work with. [S
Need a front photo for us to ponder Dozer.

 

[dutch]

Nothin out of wack from where I sit...maybe the paint on the 440 As for the rad shell, I would use the bead in the door panel as a guide line level with the lower edge of the hood. I really like the long straight lines on this car... Hard to tell from the pics but it looks like it may need to drop a hair or two to get it right, but that`s really just because you mentioned it

 

[DozerII]

Nice profile look. How much room do you have up front to work with. [S
Need a front photo for us to ponder Dozer.

Thanks Bman I have lots of room up front for a thick rad, here's some pics.

Nothin out of wack from where I sit...maybe the paint on the 440 As for the rad shell, I would use the bead in the door panel as a guide line level with the lower edge of the hood. I really like the long straight lines on this car... Hard to tell from the pics but it looks like it may need to drop a hair or two to get it right, but that`s really just because you mentioned it

[

Thanks dutch, the engine paint will be changing. I used your idea and ran a string line from the body line out past the grill shell and found the shell was sitting on the rack on the drivers side lifting it 1/2, all good now.

 

[BillM]

I'm with Dutch and BMan....lines look good to me. Looks like you've done a nice job of getting all the wheels centered in the wheel openings (a pet peeve of mine - I hate it when the wheels aren't in the right spot in the fenders!)

Looking good!

 

[kenny c]

[cl

 

[MercuryMac]

No complaints here, Dozer. Lookin' Good.

 

[DozerII]

Thanks guys.

 

[forbigpicture]

Looks great Dozer....what control valve are you using for
the air ride ....

[P[P

 

[Old Iron]

[cl[cl[cl
[P[P[P

 

[animal]

I really like the stance and profile. The 440 looks good in there! [cl[cl

 

[lowbudget50]

Looking good man!!!

 

[Kasselyn29]

NICE Work and a lot if it! Looks good

 

[DozerII]

Looks great Dozer....what control valve are you using for
the air ride ....

[P[P

It's the manual control from Chassis Tech/ Airbagit

[cl[cl[cl
[P[P[P

I really like the stance and profile. The 440 looks good in there! [cl[cl

Looking good man!!!

NICE Work and a lot if it! Looks good

Thanks everyone,I'll just keep plugging away at it.

 

[myboat@i]

Nice work Glen shez a bute for shure [dr

 

[smallfoot]

I'm thinking you hit the mark...[cl