DozerII
Well-known member
Hey MM I have a flathead pan that was in the cab of one of the trucks I dragged home. 48 or49 Merc I can post a pic of it you want.
36 Ford truck on Ranger
- Thread starter MercuryMac
- Start date
Help Support Rat Rods Rule:
MercuryMac
Builder Junky!
Part of the problem is that I don't like throwing away something that is 95% good and only a measly 5% bad. I have to fix it, usually at great cost. And the other part of the problem is, I assumed that I couldn't buy a new oil pan.
Thank you Dozer, that sounds like an 8BA oil pan which is what I need. The older, 59A ones are quite a bit different with part of the belhousing on them. I will keep yours in mind if mine still leaks. Yours has probably never been sitting in the dirt with a whole motor weighting it down.
Thank you Dozer, that sounds like an 8BA oil pan which is what I need. The older, 59A ones are quite a bit different with part of the belhousing on them. I will keep yours in mind if mine still leaks. Yours has probably never been sitting in the dirt with a whole motor weighting it down.
Dr Crankenstein
Rocket Surgeon
Mac: I fixed a cracked pan (on the car) with JB Weld. It lasted a few years until we pulled the motor... the repair was still good!
.
.
MercuryMac
Builder Junky!
Thanks for boosting my confidence Dr. C.. I didn't get much done on the pan today, Oh, I guess I let the JB Weld cure, that's something. I sanded the outside hardened putty down somewhat.
Mostly, today, I patched up the lawn where some aggressive turkey snowplowed heavy snow before the frost was in the ground, last early winter. I cursed that turkey out volumously, ----last winter and then again this spring. I am going to make little safety skis for my blade.
Mostly, today, I patched up the lawn where some aggressive turkey snowplowed heavy snow before the frost was in the ground, last early winter. I cursed that turkey out volumously, ----last winter and then again this spring. I am going to make little safety skis for my blade.
DozerII
Well-known member
That must be the same turkey that deposits buckets full of snow and gravel on my lawn when he's pushing snow with the tractor
MercuryMac
Builder Junky!
I think he's one of those 'unlucky' guys that a good cursing out doesn't help. Maybe we'll have to talk to him 'by hand'.
DozerII
Well-known member
MercuryMac
Builder Junky!
I primed the pan after a lot of sanding and when it was dry I painted it blue. The shop phoned last night to say come and get your motor. I think I will.
An old friend phoned the other night and asked if I would help him clean up his yard because he is creepin' up on ninety years old. Was I still interested in '36 Ford trucks. Yes!!! I said. Well, come and get mine, it's in the barn. I didn't have a plan for this truck on that short of notice, but said yes anyhow. This is a true barnfind, guys. Pics.
An old friend phoned the other night and asked if I would help him clean up his yard because he is creepin' up on ninety years old. Was I still interested in '36 Ford trucks. Yes!!! I said. Well, come and get mine, it's in the barn. I didn't have a plan for this truck on that short of notice, but said yes anyhow. This is a true barnfind, guys. Pics.
Attachments
smallfoot
He's rockin' the "Nuttin Special"!
Nice work on the pan and what a deal on the 36...[cl
Old Iron
Well-known member
^^^X2^^^ on the pan
And what a neat ole truck[ddd[ddd[ddd
And what a neat ole truck
[ddd[ddd[ddd
Skip
Well-known member
That is a beauty. [cl
skull
''SARCASM: just one of his many talents.''
red truck
we wondered why you weren't at the meeting, now we know guess you'll have to do 2 next week
SWEEEET[dr
nice of him to give the truck to some one who will do something with her, so many times they just sit and rot away.
Later
we wondered why you weren't at the meeting, now we know
guess you'll have to do 2 next weekSWEEEET[dr
nice of him to give the truck to some one who will do something with her, so many times they just sit and rot away.
Later
05snopro440
Well-known member
That 36 is a beauty! Lucky duck!
Dr Crankenstein
Rocket Surgeon
I see a flat deck and a tractor on said deck...
.
.
Torchie
Well-known member
[cl Torchie
Bamamav
Well-known member
I see a flatbed with ramps too. That truck is in too good of shape to cut it up, I'd leave it as a bigger ton job.
MercuryMac
Builder Junky!
Yes guys, I'm pretty sure it'll stay a two ton. I wanted to end up with a thirty six to pull that trailer [in the picture] with old tractors on it or old cars or old trucks, but this was a surprize to me so I haven't dreamt up enough images yet of what I want.
Skull, I'm under the impression that you can't come to the meetings if you're a backslider, bad enough to be red in the face like me. I haven't even told you that I also brought home an old two cylinder John Deere and a pull-type swather. At the meeting there, would be a lot of gasping and some guys would even put their hand over their mouth, when I made my confession.
Skull, I'm under the impression that you can't come to the meetings if you're a backslider, bad enough to be red in the face like me. I haven't even told you that I also brought home an old two cylinder John Deere and a pull-type swather. At the meeting there, would be a lot of gasping and some guys would even put their hand over their mouth, when I made my confession.
MercuryMac
Builder Junky!
Anyway, back to our regularly scheduled program, the making of a half-ton '36 Ford.
I got my rebuilt motor [268 ci Mercury flathead] home but promptly went on holidays, so nothing happened for a while. Now I have got my flywheel lathed down smooth and tacked on the starter ring gear. Running a 6v starter on 12vs livens up the starting process a lot, but the downside is that the starter hits a little too hard and can work the ring gear off, so I tacked it on. I had bought new water pumps, but they were painted universal black so they got painted blue today. I also painted the thermostat housings and dipstick.
I got my rebuilt motor [268 ci Mercury flathead] home but promptly went on holidays, so nothing happened for a while. Now I have got my flywheel lathed down smooth and tacked on the starter ring gear. Running a 6v starter on 12vs livens up the starting process a lot, but the downside is that the starter hits a little too hard and can work the ring gear off, so I tacked it on. I had bought new water pumps, but they were painted universal black so they got painted blue today. I also painted the thermostat housings and dipstick.
Attachments
Old Iron
Well-known member
[P[P[P
