Search results

http://dennyshangout.com/dennysplace/ This place has tons of infomation on all kinds of makes and models. Great sorts for those hard to find answers.

Brought this axle the other day and the seller did not know the year. After doing some cleaning on it I discovered "Ford" stamped on the backing plates so that answered one question I had. Axle casting number is 21Y-3010. I now need to know what year it is. I think it came off a 3/4-1 ton...

I got banned from the billet site today, No reason given, no chance of getting back in there.........????????????:confused: Seems from what I have read on other sites I am not the only one this has happen to in resent weeks without any reason given. Any one else want to comment on this or know...

Can someone identify this backing plate and front drum. I know the axle I am using came from a 1951 Chevy truck and the spindles are from 1949-1954 Chevy also but I have no idea what the backing plates came off of except possible a car. I have check the pattern on the drum against truck drums...

I am at the point in my build to where I want to see if I can get this old engine fired up.[dr I motor has been setting for several years but turns over great with a wrench. I know I will have to get it primed with oil. Pull the plugs and clean and set them and set the point gap. Can someone...

I am searching for a camshaft for my 1964 Chevy 230 CI with a mild thump to it.[dr Nothing hard hitting, just mild with enough sound to talk to let people know it isnt stock. Also want to run stock lifters and springs. [S I dont know what lift or duration to ask for.[S Need suggestions as to...

OK I am at the part of my build to where I need to mount the radius rods on the front axle. What I need to know is how to go about adjusting them once I have them on to get the 6-8 degree angle needed? Larry

I am wanting to build my own design for a spring perch and was wondering if 1/4 inch flat stock will be strong enough? The design will look kinda like your speedway design. 4 inches wide and 8 inches long with sides being 2-3 inches tall. Any comments will be appreciated. Thanks Larry

I am thinking about running a 2 link suspension from a late 60's to early 70's Chevy truck. What are the pros and cons of a setup like this? The car will only weight about 2200 lbs when finished. Engine is a stock 230cid straight six with a powerglide so there is not alot of torque. Rearend is...

Anyone know what this frontend is out of.:confused: It was a freebie and couldnt pass it up.:D Thanks Larry

I have a rearend out of a 80 model F150. After setting the engine in the frame and centering it between the rails I fabricated my engine mounts and got those tacked in place. I put the rearend in position and the yoke on the rearend is 2 inches to the left of center looking from the front. I...

Ok all you carb gurus, I need some help here with this one. Its a rare beauty made by Woodworth. I found one, yes only one, on E-bay for a buy now price of $199.95. http://cgi.ebay.com/ebaymotors/Woodw...mZ320248767550 What I need is more info on this lil jewel. It's a Woodworth VCCV 75...

Ok guys this is addressed more to the older guys. I need help in remembering what kind of carburator I need. The older I get the more memory I lose. I'm confused as a termite in a yoyo. I have an 4 bbl intake that fits a 230CID stock six. What kind of carb will work on this and not flood it...

OK I know this may be a strange question but its something thats been bugging me. I have a front axle that has crossover steering and I am wondering if it can be turned around, putting the tierod on the front side of the axle and make it steer from the left side and still be safe? Have I...

I am needing some ideas on how to fab up a shifter for a powerglide tranny because $$$'s are so few and far between lately I cant afford to purchase one. If anyone has any ideas on how to build a safe shifter that won't pop out of gear or into Reverse or Park while motoring along I sure would...

I posted this same question on KB site. Searching for some suggestions here also on this subject. I have a 1964 Chevy 235ci straight six (stock) and need to know what kind of intake to look for. I want to bump up the cam a little to make it sound good but nothing to wild and put on a headed if...

Anyone have a drawing of a beer keg that has been converted into a gas tank and what connections are needed? What is needed to make the filler spout from. I have finally located a 15.5 gal keg and need to know what to do from here to convert it. Any help would be appreciated. Thanks

Looking for a rear end for my ride but dont know which one to look for. I want something with the hoghead aka pumkin in the center with axle of equal lengths. Running a 230 ci with powerglide tranny. Frame is 35" wide in the rear. Any suggestings? Help!!!:confused:

Just wanted to post a special thread and greet everyone with a very Merry Christmas and may the blessings of our Lord and Saviour Jesus Christ be with you all this coming New Year. Lets not forget what the meaning of Christmas is. We received the greatest gift of all in the virgin birth of my...

Bought a Hobart 135, 110 volt welder from a fellow who replied to my request on Graigslist last week. Gave 300 for the used welder which at the time seemed to be a good deal being the guy claimed to work for Hobart and trained through Hobart. I did try it out at his house for a couple of small...